Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
formech_1372:formech_1372 [2023/05/10 06:07] – [PS - Polystyrene] formlab | formech_1372:formech_1372 [2023/12/18 00:46] – [Control panel] formlab | ||
---|---|---|---|
Line 37: | Line 37: | ||
==== Tested mould materials include: ==== | ==== Tested mould materials include: ==== | ||
* **Plaster** | * **Plaster** | ||
- | * <color orange> | + | * <color orange> |
* **Wood** | * **Wood** | ||
* <color orange> | * <color orange> | ||
Line 50: | Line 50: | ||
* **3D printed parts** | * **3D printed parts** | ||
* <color red> | * <color red> | ||
+ | * Plastic deforms: infill becomes visible if not enough top layers or walls. | ||
* ... | * ... | ||
Line 186: | Line 187: | ||
* **Bubble moulding**: The table should be lowered. If it's in the up-position, | * **Bubble moulding**: The table should be lowered. If it's in the up-position, | ||
+ | |||
+ | ===== Drying sheets with the oven ===== | ||
+ | |||
+ | Use one of the ceramics oven in the metal atelier.\\ | ||
+ | The control cabinet is behind the oven. \\ | ||
+ | {{: | ||
+ | |||
+ | |||
+ | Get the key from Peter to be able to power on the oven.\\ | ||
+ | To turn on the oven, insert the key and turn it to the right. Then turn the red knob to the right.\\ | ||
+ | |||
+ | ==== Control panel ==== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | * There are 9 programs | ||
+ | * Each program can have multiple segments | ||
+ | * Example: segment 1: warm up to 70° in 30 min, segment 2: keep that temperature for 4 hours | ||
+ | * Each segment has 2 values: a temperature, | ||
+ | |||
+ | |||
+ | - Press ' | ||
+ | - Nothing is on here yet. (This might change in the future) | ||
+ | - Press until there' | ||
+ | - In the future there might be a paper with an explanation of what programs do what. I could have a fixed entry on the list | ||
+ | - Segment 1' is blinking. Use the up-down arrows to set a target temperature | ||
+ | - Press the --> arrow to go to the time value | ||
+ | - Set the time with the up-down arrows | ||
+ | - When ready, press the stop / start button to start the oven. | ||
+ | |||
+ | ==== Suggested program ==== | ||
+ | |||
+ | * Segment 1: temp: 70° time: 30 min | ||
+ | * Segment 2: temp: 70° time: 4 hours | ||
+ | * Segment 3: temp: 0° time: 30 min | ||
===== Clamping tips for high gauge sheets ===== | ===== Clamping tips for high gauge sheets ===== | ||
* Apply 80 grit strips of sand paper to the underside of the clamp frame to provide more grip on the sheet. The strips can be held in place with a good quality double sided tape, contact adhesive or preferably a silicone adhesive to take the heat. | * Apply 80 grit strips of sand paper to the underside of the clamp frame to provide more grip on the sheet. The strips can be held in place with a good quality double sided tape, contact adhesive or preferably a silicone adhesive to take the heat. |