Differences

This shows you the differences between two versions of the page.

--- hyrel:bees_wax [2020/10/12 07:17] – [Cleaning] formlab
+++ hyrel:bees_wax [2020/10/13 05:34] (current) – [Settings / profiles] formlab
@@ Line 9: / Line 9: @@
 ===== Settings / profiles =====
-  - 1,6w 0,2z 15f 0pct
+  * 1,6w 0,2z 15f 0pct
-    - 3D object: Cone
+    * 3D object: Cone
-    - 35°C filament, no fan, no bed
+    * 35°C filament, no fan, no bed
-    - --> FAIL
+    * --> FAIL
-  - 1,6w 0,4z 7f 0pct
+  * 1,6w 0,4z 7f 0pct
-    - 3D object: Cone
+    * 3D object: Cone
-    - 35°C filament, no fan, no bed
+    * 35°C filament, no fan, no bed
-    - --> Filament stopped adhering to print bed after a while
+    * --> Filament stopped adhering to print bed after a while
-      - No random layer restarts
+      * No random layer restarts
-      - Higher layer height
+      * Higher layer height
-      - much more flow
+      * much more flow
-      - First layers are okay, Adhesion only occurs on motor override
+      * First layers are okay, Adhesion only occurs on motor override
-  - 1,6w 0,8z 7f 0pct
+  * 1,6w 0,8z 7f 0pct
-    - 35°C filament, no fan, no bed
+    * 35°C filament, no fan, no bed
-      - OK: first layer sticks with uhu-glue
+      * OK: first layer sticks with uhu-glue
-      - After ±3 layers: material doesn't want to stick onto itself.
+      * After ±3 layers: material doesn't want to stick onto itself.
-      - --> Increase extrusion width from  1.7 to 2.2 (future me: extrusion width doesn't change material flow. It just changes the distance between lines)
+      * --> Increase extrusion width from  1.7 to 2.2 (future me: extrusion width doesn't change material flow. It just changes the distance between lines)
-      - --> Layer height 1mm everywhere
+      * --> Layer height 1mm everywhere
-    - Beeswax 01
+    * Beeswax 01
-      - 35°C filament, no fan, no bed
+      * 35°C filament, no fan, no bed
-      - Using Uhu-glue
+      * Using Uhu-glue
-      - There are gaps between lines
+      * There are gaps between lines
-      - not enough extrusion
+      * not enough extrusion
-      -
-    -
+/04/2019
+D model: cone
+  * Beeswax 01 (0,8z 7f)
+    * nozzle: 35°C
+    * bed: 25°C
+    * result: Prints beautifully. Z-axis skipping (Z-axis motion is too fast). Layers delaminate easily, as they are not fused.
+  * Beeswax 01
+    * nozzle: **40°C**
+    * bed: 25°C
+    * result: same as above
+  * Beeswax 01
+    * nozzle **45°C**
+    * bed: 25°C
+    * result: flakey / grainy texture, but stronger layer adhesion.
+  * Beeswax 01
+    * nozzle: **50°C**
+    * bed: 25°C
+    * result: super flakey
+  * Beeswax 01
+    * nozzle: 50°C
+    * bed: 25°C
+    * **warm up time: 15min**
+    * result: a little more consistent
+  * Beeswax 01
+    * nozzle: 50°C
+    * bed: 25°C
+    * warm up time: **40min**
+    * result: same as above
+  * Beeswax 01
+    * nozzle: **55°C**
+    * bed: 25°C
+    * warm up time: **30min**
+    * result: separated material: half oil, half solid. 3D print has a dripped texture. The tip of the syringe is cooler. The body of the syringe is much hotter.
+  * Beeswax 02 (1w 0,5z 7f)
+    * nozzle: **60°C**
+    * bed: 25°C
+    * warm up time: **50min**
+    * result: Almost completely liquid. Too liquid for the nozzle width.
+  * Beeswax 03 (1w **0,15z** 7f)
+    * nozzle: **60°C**
+    * bed: 25°C
+    * result: Still a little smudgy. Good consistency: creates homogenous lines.
+/04/2019
+  * Beeswax 4 (0,6w 0,15z 7f)
+    * filament: 70°C
+    * shape: cone
+    * result: a luer tip with 0,6mm inner diameter cools the wax down too much, resulting in jams and sudden eruptions of hot wax.
+  *Beeswax 4 (1,18w 0,15z 7f)
+    * filament: 70°C
+    * shape: cone
+    * result: OK, but printing too slow: cools down too fast
+  *Beeswax 4 (1,18w 0,15z **20f**)
+    * filament: 70°C
+    * shape: cone
+    * result: Material flow stops. There is a weird buzz which I think is an unprime event.
+  *Beeswax 4 (1,18w 0,15z 20f)
+    * filament: 70°C
+    * shape: cone
+    * **head control**: unprime set to zero
+    * result:?
+  * Beeswax 5
+    * filament: 35°C
+    * shape: vessel v1
+    * result: layers too thick, had to change material flow rate multiplier to 1.5.